killowords.blogg.se - N1mm logger and winkey config for ft897d

N1MM LOGGER AND WINKEY CONFIG FOR FT897D HOW TO
N1MM LOGGER AND WINKEY CONFIG FOR FT897D MANUAL
N1MM LOGGER AND WINKEY CONFIG FOR FT897D SOFTWARE
N1MM LOGGER AND WINKEY CONFIG FOR FT897D PLUS

To make this happen open N1MM config section and click on the broadcast data tab. These are my settings for using the Digital Master app inside HRD for CW, RTTY etc. In your sound settings, both the MIC and SPEAKERS MUST SAY USB That last one was preventing me from keying up my rig. Setup JTAlert to use a text file log and when a QSO gets logged in WSJT, JTAlert will send N1MM the QSO details and will be logged in N1MM. For the Radio, menu option 3138400, 60RTS, 70 Rear, 71RTS, 72USB and most important for TX 144DATA. When I want to use the built-in keyer with my iambic paddle, I just push the KEYER button on the radio. If the user is using WSJT they will need to also be using JTAlert. Select the Digital Modes tab in the N1MM Logger Configurer. Do not configure a Digital Port in N1MM Logger or a FSK Port in Router.

AFSK and PSK do not require the use of a digital port for each radio. This configuration is for AFSK RTTY and PSK. (the rear jack is configured as a straight key) N1MM Logger supports the MMTTY Engine, MMVARI and/or an external TNC for RTTY contesting. I run my keying interface off the rear KEY jack and my iambic paddle off of the front KEY jack and use the following menu settings: When you have N1MM keying the radio, you do not want the internal keyer on the radio functional.

N1MM LOGGER AND WINKEY CONFIG FOR FT897D MANUAL

On of the FT-950 manual you can see the warning about not using a 2-conductor plug - and you'll want to follow the wiring for "straight key"Īlso, make sure that the KEYER button is pressed until "KEYER" is _not_ displayed on the screen. No wires would be connected to the ring - see picture

Clearing Rttyrite Sections from writelog.Click to expand.If you are connecting a keying interface, then you are only going to use wire up the sleeve and tip.

Once you have MMTTY set up in DI-1, you are now ready to Set up 2Tone in a Receive-only Digital Interface window. Once you have MMTTY working, then go back to N1MM. The best way to troubleshoot is to close N1MM and open the standalone MMTTY program. If you are not printing the signal or see the presence of noise in the RTTY Engine 1 window, then something is not set up correctly. JTDX: 'Enable automatic logging of QSO' should be checked in JTDX setting table. When you click OK then QSO is logged in WSJT-X and Logger32. When WSJT-X send 73/RR73 then Log QSO window appears. WSJT-X: 'Prompt me to log QSO' should be checked in WSJT-X setting table. Note: With your radio on, tune in a RTTY signal. QSO logging' option is checked in UDP BandMap Config menu. Logged on N1MM latest Revision with BERU support - great to have score appear automaticaaly in previous years Ive used N1MM and scored manually after event. A3S at 30 feet 80m & 40m Dipoles at 30 feet R8 Vertical.

N1MM LOGGER AND WINKEY CONFIG FOR FT897D PLUS

IC-7000 PLUS ANTIQUE SB200 Linear About 400w. (If your radio is turned on and MMTTY has already been set up to receive on your sound card, you may see the presence of noise in the display and you may see random noise characters in the Digital Interface window. Rig K3 100w ant 80m inv L 40m GP and HF vertical doublet.

Drag it away from other windows so they don’t overlap. So now we will start to configure N1MM Logger+ for use with WSJT-X.

N1MM LOGGER AND WINKEY CONFIG FOR FT897D HOW TO

The familiar MMTTY control panel, called “RTTY Engine 1”, should appear as shown in Figure 3-5. This will be a step by step instructional on how to WSJT-X, JTAlert and N1MM Logger+. Go to the Interface pull-down menu at the top of the Digital Interface window and select MMTTY as shown in Figure 3-3. Ham Radio Deluxe, WSJT-X and JTAlert can be configured with a little workaround.

With the two virtual COM ports in the Icom 7160, N1MM Logger+ can be configured easily to operate RTTY (FSK).

N1MM LOGGER AND WINKEY CONFIG FOR FT897D SOFTWARE

If the Main Entry Window is on top of the Digital Interface window, move the Main Entry Window away from the Digital Interface window so they don’t overlap each other. The new Icom 7610 isnt listed in many Ham Radio software programs, but it is in N1MM Logger+ and MacloggerDX. The Digital Interface (DI) window opens up to MMVARI by default.